angle keel roll forming machine

Angle keel roll forming machine
Angle keel roll forming machine equipment consists of: discharge machine, the guide frame, forming the host, correction means, length cutting portion, receiving station, consisting of electrical control and so on. Bed as steel weldments. And for tempering, eliminate stress, avoid deformation of the fuselage.

A detailed description:
Triangle keel machine performance parameters
1. Unit rolling capacity: Wide ≤150mm, sheet thickness 0.6-2.0mm
2. Production speed: 6-13 m / min
3. The total installed capacity: about 5.5kw
4. Production area: 15 meters long, 2.5 meters wide X
Triangle keel machine is a strip of material, by continuous cold roll forming, producing complex cross-section profiles (products: light steel keel, paint keel, keel card, all kinds of construction profiles, steel, steel-lined door profiles, speed Hulan, etc.) and different specifications of cold-formed, paint unit equipment, PLC control.
Angle keel roll forming machine equipment consists of: discharge machine, the guide frame, forming the host, correction means, length cutting portion, receiving station, consisting of electrical control and so on.
I produced the triangular keel machine has the following advantages:
1. Device control PLC control, set up the system in normal production multiple security.
2. Bed as steel weldments. And for tempering, eliminate stress, avoid deformation of the fuselage.
3. The molded cast iron frame structure, and by tempering. Strong high, long service life.
4. The roller shaft material is 40Cr, and after quenching, hardness of HB280.
5. The mold material is GCr15, quenching, hardness: HRC56-62 ℃.
6. The transmission structure for the gearbox, each molding frame has a gear box, can ensure that equipment over time, high-intensity running, and long service life.

We also have high spend light keel roll forming machin and trangular light kell machine

C purlin roll forming machine

C purlin roll forming machine

The C purlin roll forming machine, purlin processing technology belong to the field of equipment. Includes a feed station, the guide, leveling device, punching equipment, cutting equipment and molding apparatus, the molding apparatus may be C / Z-type automatic conversion, including the structural symmetry of the front roller and a rear molded member and the forming roll before conversion and after conversion component assembly, before the conversion assembly includes a power unit, a rotating shaft, angle seat and transfer roller mounted seat angle, seat angle and transfer roller mounted between the upper shaft and lower shaft through the rotary shaft rack, after the conversion assembly includes a corner seat and mating roller mounted seat angle, with the roller is mounted on the frame between the drive shaft and the lower shaft through the corner seat. The present invention may be realized C, Z-type automatic conversion and specifications automatically adjusted.

C-purlin-roll-forming-machines

C purlin forming machine technical parameters:

Host Volume: 8 meters long and 1.5 meters wide, 1.2 meters high
Weight: about 5.2 to 5.6 t
Main motor power: 11kw
Reducer: Planetary cycloid reducer
Large frame: 350mm H-beam GB
Sprocket chain: 2 inch chain sprocket
Plate thickness: 18mm
Spindle Material: 45 # steel, shaft: after processing φ80mm, after quenching from finishing
Leveling machine: nine roller leveling, 45 # steel seamless steel pipe, finishing, made of hard chrome plated
Roll the die: all Gr15 (bearing steel) by forging, finishing, quenching (hardness of 52 ° ~ 56 °), keyway cutting line cutting, surface hard chrome plating from
Adjustment set: C-shaped steel purlin forming machine with 45 # steel seamless steel pipe finishing, zinc plated, line cutting cutting snap together
Roll Rows: 12
Auxiliary wheels: 6 rows of auxiliary wheel adjustment
Rollable thickness: (2 ~ 3) mm
Purpose: purlins

This is one of the standard of the c purlin roll forming machine.

C-purlin-roll-forming-machine
C purlin forming machine is mainly composed of passive material rack, material rack chassis, the feed import platform, screed, forming the host, punching device, forming cutting device, hydraulic station, computer control cabinet composed of several parts.
By C-shaped steel purlin roll forming machine C-purlins finished with good bending compression resistance, good flatness, automatic fixed-length cutting, automatic punching, high degree of automation, quick and easy installation. C purlin forming machine can be used as medium-sized industrial civil buildings by the main body of the force structures, such as factories, warehouses, machine garages, hangars, exhibition halls, theaters, stadiums, fairs trellis roof load and load-bearing wall support.

If you want to know more c purline forming machine you can contact me with email   roofingmachine@zhongtuocn.com

You also can visit the main metal rolling machine to know more information.

C beam machine

C-beam machine
working principle:
C-beam machine known as C-shaped steel purlin machine, mainly by passive loading rack, leveling device, punching device, after forming cutting device, hydraulic station, computer control systems and other components, the use of automatic flying saw punching and easy operation Features. The main purpose of the product can be used as the main medium-sized industrial civil buildings by the force structure.
C-beam machine technical parameters:
Device Length: 7600mm * 1000mm width 950mm * high
Power equipment: 11KW, hydraulic power station: 11KW
Roller bearing steel (GR15), annealed forged
Base with 320 I-beam
By using five on four leveling, to ensure smooth
Quadratic formula molding, to ensure product Founder and right angles, the upper size can be produced
Rolling material thickness: 1.5mm-3mm (according to user requirements and design thickness)
C steel rolling width: 80mm-300mm
Rolling speed: 8-9m / min

Broken-C-Purlines-roll-forming-machines
Use of new steel butt-regulatory sets, simple, fast, secure
C-beam machine known as C-shaped steel purlin machine, mainly by passive loading rack, leveling device, punching device, after forming cutting device, hydraulic station, computer control systems and other components, the use of automatic flying saw punching and easy operation Features. The main purpose of the product can be used as the main medium-sized industrial civil buildings by the force structure.
C steel machine with color plate molding machine is different, it is hydraulically powered, and great power, usually around 22KW, similar to shearing bending machine, general control process is complex, the use of PLC control.
C-beam machine by rolling the C purlin finished with good bending compression resistance, good flatness, automatic fixed-length cutting, automatic punching, high degree of automation, quick and easy installation. Products can be used as the main medium-sized industrial civil force structure, such as factories, warehouses, machine garages, hangars, exhibition halls, theaters, stadiums, fairs trellis roof load and load-bearing wall support.

Broken-C-Purlines-roll-forming-machines-1
C steel machine equipment operation and precautions:
Hand put blanks, blanks taken procedures: Before using the device, check the connection is solid throughout, mounting bolts, whether or tighten the nut around the chassis lubrication should add a little oil to power-up test machine, first empty running carefully observed , with or without vibration, noise, oil window is to oil, whether coordinated motion components before you can install all the normal mold, mold installation, must be cut off, by hand moving belt or gear motor, so indexing table, and carriage rise to the highest point, it is best to use an object supported between the table and the bottom surface of the slide to slip seat natural fall, causing the accident.

Combined-UC-light-keel-machine
C-shaped steel machine equipment process:
From the end of the strip into the device, through a variety of roll pressed into C-shaped steel from the head sent. Traditional process, after the C-shaped steel pressing need to manually cut length, and then transported to the punching device in accordance with customer requirements size drilling, production can not be continuous, the efficiency is not high.

We also have Fully automatic Interchange C/Z purlin roll forming machine,C & U & Z purline machine

Combined-UC-light-keel-machine1

 

You also can contace email   roofingmachine@zhongtuocn.com

Tile press power analysis considerations

Tile press power analysis considerations
1.the electrician is necessary to know the species and plant functional electrical circuits and electrical equipment, electrical equipment is not functioning abundant know, to stop the adventure homework.
2. should be scheduled to view daily Electrical cables, motors, electric console and other equipment status, view found in the title, it is necessary and timely treatment. When viewing the motor temperature, first check without electricity, and then back to the experiment.
3.in addition to temporary construction of electricity or temporary measures adopted, the frame does not allow temporary wires, does not allow chaos to hang lights, things look and welders use safety switches and sockets, the original electrical wiring can not change the private line.
4. according to the delineation of electrical equipment inspection maintenance schedule, without having to electrical equipment line to be completely removed.
5.part of the power outage homework, when the electric body near 0.9 m or less from the inspection staff who have to use dry wood rubber or insulating materials for reliable temporary masking.
6. the use of electric things, electric shock and maintenance.
7. the use of ladders, ladder viewpoint between 60 degrees and the situation is appropriate, when using ladders cement situation, there must be ways to slip, and someone hold the ladder.
8. tile machinery of any conductive parts found grounded before power is not cut off, in addition to rescue an electric shock, and will not allow close proximity from four meters outside the interior from 1.8 m to step voltage from injury.
9. when the repair equipment, switches and pull down the knife, and the knife is necessary to hang the switch at the “Suppression of the contract, it was a job,” the warning signs on the cover bar and live equipment to stop the passage of the aisle, should hang “stop, high pressure risk” warning signs, work address should hang “should this job,” the warning signs.

Useing of the JCH roll forming machine

Useing of the JCH roll forming machine

Use the JCH roll forming machine must first start the motor idling, unusual view is not the case, the machine into the position of the two plates intercourse, while adjusting the height of the feet on both sides of the roller pressure is not something you want to position.
JCH roll forming machine because it is using more dilute vibration molding concrete material rather than compacted inside the pores more, so poor flexural strength of this pressure-watt machine. The type of tile press very much, Kok Chi tile press is a good performance, using the electronic control system screen display of text, use very simple, beginners can use this tile press, then Kok Chi tile press machine using precautions, what does? EAST pressure tile machinery factory for you in detail.

Wall-angel-roll-forming-machine-16

① Use JCH roll forming machine must first start the motor idling, view is not unusualcircumstances, the machine into two plates intercourse position while adjusting the height of the feet on both sides of the roller is not something to be pressure position.Under general condition
② plate bending width of 11-15 mm in between, otherwise the machine will be very easy to fall off. It must ensure that the two plates intercoursepositions can be tightly buckle together, must not be disengaged, otherwise the machine will be off.

③ start tile press, who must use the machine and walk around, and if the front of thetwo plates have disengaged from the stop plate must be flattened before boot.

④ Since JCH roll forming machine is forming a platen during greater resistance, in order to ensure the life of the motor, please stop after every 30 minutes for 5 minutes.

⑤ use and handling time, can not be bumps wheel, do not use blunt beating wheel.When not used for long each part should be carried out oil lubrication, while the package was better to avoid leakage occurs.

We also have another cold roll forming machine like shutter door roll forming machine ,  keel roll forming machine 

If you need this machine you can contact us with email  roofingmachine@zhongtuocn.com

 

Z purline roll forming machine main purposes and advantages

Z purline roll forming machine main purposes and advantages

Z purline steel is not only a durable and economical advantages, while z steel throughout the production process of clean, environmentally friendly, z steel addition to the application with a number of large steel structure into the room, still rolling stock, transport, shelves, appliances cabinets, highway guardrail, container and other industries are widely used. Z-shaped steel profiles belong efficient and economical cutting surface and cross-sectional shape and reasonable, can play better performance, improve the bearing capacity of the CD.

Z purline roll forming achine Size adjustable, compressive strength, etc. Widely used in automobiles, railway vehicles, building windows and doors, transportation, shelves, electrical cabinets, highway guardrail, construction steel, container, steel formwork and scaffolding, solar energy bracket shipbuilding, bridges, transmission towers, steel sheet pile, cable tray, agricultural machinery, furniture, storage, rail, steel keel, vegetable greenhouses, pipe supports, municipal construction and other fields.

z purline roll forming machine
Z purline roll forming machine applications more widely, particularly with regard to the advantage of the majority of people just type z may know very little, its most significant advantage is that by the use of durable. Now every part of the Z-beam can be coated with zinc, and strong resistance coating, can accept during transportation and use of mechanical damage suffered. Z galvanized steel construction process than the other coating method is more convenient, but also prevents the device after brushing on the site.

z purline roll forming machine

If you need the Z purline machine  , C purline machine and C/Z purline roll forming machine   you can contact us with email

roofingmachine@zhongtuocn.com

z purline roll forming machine

 

Quotation-60*27-28*27 Light Keel Roll Forming Machine

60*27-28*27 Light Keel Roll Forming Machine is something like combined type light keel machine. By this one machine, you can make 60x27mm stud, 27x28mm track and others. All those three elements is quite important for drywall building. When you need to start drywall work project, I feel this one machine is enough for you.

The machine can process material: GI  and others               Material thickness:  0.4—0.8mm
Material hardness: 550 MPA—350 MPA                                  Formed width: 28/60mm
Forming speed: 20m/min

Here are some drawing profile for your reference:

1

The machine is composed by the following elements: decoiler, leveling beach, roll forming machine, shearing and punching system and the runout table. The machine is fully automatic and controlled by PLC. So you can control machine working speed, shearing length and accuracy.

Here are the machine elements details for your reference:

Decoiler:

Usage: It is used to support the steel coil and uncoil it in a turntable way. Passive uncoil pulled by roll forming system
Loading capacity: 1.5T       Uncoiling width: 300mm       Inner diameter: 450-550mm

Entry Beach

Usage: Put the raw material(steel plate) through the beach to manufacture and process, it can guarantee that the products are neat, parallel and everything is uniformity. Please refer to the equipment regulation to know the function of locate board.

Main Roll Forming System

Feature : Ensure stability , precision and lifetime.
Usage: In order to keep the product shape and precision, adopts welded sheet structure, motor reducer drive, gear transmission( the first and the last roller, the down roller should be attached with the upper one with the gear drive.), roller surfaces polishing, hard plating , heat treatment and galvanization treatment . The polished surface and the heat treatment towards the molds also can keep the molding plate surface smooth and not easy to be marked when it is being stamped.
Length of the main part: about 3000х1000х1400
Weight of main part: 3 tons
Voltage : 380V/50HZ3Phase (as customer’s request)
Roller fixer : Guide column
Frame : middle plate welded
Memorial arch frame type
Frame thickness:25mm
Drive mode: gear
Material of rollers: GCr12MoV
Material of shafts: 45# steel with tempering
Diameter of shafts: φ40mm
Number of rollers : 10 rollers
Main power: 3kw
Cycloidal planetary gear speed reducer)
Double working lines on the machine to finish the two profiles. Change the feeding unit to make another profile, the cutting head can move left and right by hand!

Shearing Mechanism

Feature : Ensure stability, precision and cutting speed
Function : Automatic cutting controlled by PLC
It adopts the hydraulic drive and automatic location to decide the dimension and cut the target products.
Material of blades: Gcr12MoV quenched
Power supply : hydraulic power
Frame : Pillar style with rack & pinion system
Stroke switch :  non-contact photoelectric switch
Components: It contains one set of cutting tools, one hydraulic tank and one cutter machine.

Here is the each part picture of machine for your reference:

purline

For this machine, if you want to know more information, please contact me at any time or sending us an email to cnzt002@zhongtuocn.com