Guardrail Forming Machine

Introduction
Express road guardrall panel is made from hot rolled steel strips,and straightened,holes punched,roll formed,and cut to length by WLGR series guardrall roll forming machine. The finished products are of many features. Such as high effiency,high automatization,less labor.and etc.This machine integrates the technologies of cold roll forming,punching,automatic stack,and automatic controlling.
WLGR series guardrail roll forming machine consists of uncoiling system,straightening system,scrao edge cutting,levelling guillotineshearing system,holes punching system,cold roll forming system,cutting to length system,automatic stacker system,electric controlling system,hydraulic system,automatic controlling system,and so on.

Guardrail Forming Machine
Working Flow
Uncoiling-sheet Guiding-Straightening&Levelling-Scrap Cutting-Holes punching-Roll forming-Cut to length-Sheet to support table
Main Technical Parameters

Item Parameters
板型Profile Two ribs and three ribs guardraill
Material Type Steel strip
(mm)Thickness 2.5-4.0
(Mpa)Yield stress 230-300
(m/min)Max.Forming speed 20
Roller material D2
Roller driven type Gimbal transmission
Controller PLC
Operation  Touch screen+button
Hydraulic system pressure 25
Total weight  about 50000

Rib Lath Production Line

Rib lath is a kind of expanded metal lath stiffened with longiudinal ribs. The furring design of the mesh provides efficient background plaster for construction of partition. suspended celings and refurbishment works. The advantage of ribbed lath over metal lathng. that is supporting centers.which can be increased or widened.
Rib lath is ideal for relurbishing those damaged or aged masonry walls. When a key for rendering is not certain,due to disintegration or softening of the wall face, the lath should be fixed with apexes of ribs against the wall,and edge ribs of sheets connected each other,it should be wire-tied every 15cm and ends of sheets should be lapped which not less than 2.5cm.and nesting ribs are securely tied together. Stainless steel fixing should be used at sufficient intervals to hold the lath firnly in position.

Rib Lath Production Line
The Rib Lath Production Line Work Flow:
Decoiling-Punching-Feeding-Expanding&Forming-Shearing the Rib Lath to Cut to Length-Run out table

The full production line include the following components:
1.one set of sample decoiler or automatic hydraulic decoiler
2.one set of punching machine
3.two pieces of punching moulds.
4.one set of expanded and forming machine.
5.one set of cutting device.
6.one set of automatic stacker or simple run out support table.
7.one set of PLC console.
8.one set of hydraulic station.

Steel Purlin Roll Forming Machine

C,Z&M shape purlins are made from hot/cold rolled steel strips,and straightened,hole punched,cot to length,and roll formed by WLFM series steel purlin roll forming machine,Through changing spacing sleeves,the machine can change different types/sizes of purlin.

Steel Purlin Roll Forming Machine
WLPF series steel purlin roll forming machine consists of uncoiling system,straightening systems,hole punching system,shearing system,roll forming system,products support table,hydraulic system,automatic controlling system,and so on. our company has dozens of profile models for this series roll forming machine. We can design different kinds of profile and fittings for purlin machine, as per customers’requirements.

Steel Purlin Roll Forming Machine
Working Flow
Uncoiling-Sheet Guiding-Straightening&Leveling-Hole Punching-Measuring Length&Shearing -Roll Forming-Sheet to Support Table

Steel Purlin Roll Forming Machine
Main Technical Parameters

Model WLPF
Profile C purline Z purline
(mm) 100-250
Material Type steel strip
Thickness 1.5-3.0
Yield Stress 230-300
Max.Forming Speed 10-16
Roller Material Bearing steel
Roller driven type Chain transmission
Controller PLC
Operation Touch screen and button
Hydraulic system pressure 20
Hydraulic station motor power 5.5
Main motor power(kw) 18.5-22
Total power 24-27.5
Total weight about 10000

Downpipe Roll Forming Machine

Downpipe Roll Forming Machine
Closed type colour coated steel downpipe is cold rolled and automatically edge interlocked by WLDP series downpipe roll forming machine,the finished products are of many features,such as good interlocking, no leak,beautiful integrity,long time using and so on. This series machine is matched with downpipe bending (elbow)machine,used for bending and end narrowing. The angle of bending can be adjusted by manual according to engineering requirements. Colour coated steel downpipe is widely used in workshop,warehouse,hangar,gym,and so on for industry&civil buidings.
WLDP series downpipe roll forming machine consists of uncoiler,infeed guides,fixed position driven forming stations,shearing device.Hydraulic station,PLC control console and so on. Our company has dozons of profile models for this series roll forming machine
such as WLDP93-134,WLDP89-118,WLDP75-110,AND ETC. We can design different kinds of profile for downpipe machine,as per customers’ requirements.

Downpipe Roll Forming Machine
Working Flow
Uncoiling-Sheet Guiding-End Cutting-Roll Forming-Measuring Length&shearing-Sheet to Support Table
Main Technical Parameters

Item WLDP
Downpipe section specification 134*93118*89
Material Type Color steel sheet
Thickness 0.45-0.55
Yield stress 230-300
Max.Forming speed 10
Roller material 45#steel with chrome
Roller driven type  chain transmission
Controller PLC
Operation Touch screen and button
Hydraulic system pressure 12
Hydraulic station motor power 7.5
Main motor power 3
Total power 10.5
Total weight  about 8000

Automatic C steel flying saw cutting

Automatic C steel flying saw cutting

Automatic flying saw cutting, punching C steel Equipment:
From the end of the strip into the device, through a variety of roll pressed into C-shaped steel from the head sent. After gradually improve the production process, and ultimately the whole process automatic control, dramatically improved productivity, increase the technological content and added value of the client device. Improved three-step process to complete. The first step to improve and increase the length of the measuring device and flying saw, when pressed length reaches the set length flying saw action, automatically cut profiles. The second step improvements, plus a dozen side hole hydraulic punching equipment, punching four holes at once, flying saw cut from the middle, thus forming two adjacent C-shaped steel heads, tails two sides of each hole. The third step is to improve, add a device to hit the hole in the strip pressing process set by the user out of the hole spacing, the maximum it can play 16 holes. The fourth step improvements, the requirements for the new C-shaped steel profiles shot holes in the middle of the requirements of the side hole 4 hole 2 hole punching die to die, modify the program to fight side hole, making side hole punching device capable of double play in the middle hole and pitch set by user, maximum 8 groups can play two holes. This will satisfy all the requirements of the C section.

Automatic C steel flying saw cutting
Automatic C steel flying saw cutting main technical parameters:
A: Host:
1. Host Volume: 7.6 meters long, 1.5 meters wide, 0.9 meters high
2. Weight: about 5.0 tons
3. Main motor power: 11kw
4. Reducer: Planetary cycloid reducer
5. Large frame: 350H steel
6. sprocket chain: GB 45 # hardened steel
The thickness 7.: 18mm
8. Spindle: Material: 45 # steel, after quenching from finishing
9. Leveling machine: Seven roller leveler 45 # steel seamless pipe, finishing, made of hard chrome plated
10. Roll the die: all Gr15 (bearing steel) by forging, finishing, quenching (hardness of 50 ° ~ 52 °), keyway cutting line cutting, surface hard chrome plating from
11. The adjustment sleeve: 45 # steel seamless steel pipe finishing, zinc plated, line cutting cutting snap together
12. Roll Rows: 13
13. C-shaped steel Specification: adjust the width: (60 ~ 300) mm vertical wall height (30 ~ 70) mm
14. rollable thickness: (1.5 ~ 3.0) mm
15. The speed can be rolled plates (7-8) m / min
16. Model Replacement: External adjustment nut
II: Flying sawing
17. Volume: 1.3 meters long, 1.0 meters wide, 1.2 meters high
18. Quality: about 0.8 tons
19. The main motor power: 380V, 50HZ, 11KW
20. The pump station power: 380V, 50HZ, 3.0KW
21. Blade: thickness of 3.5mm, high-speed hacksaw piece
22. A hydraulic cylinder: Bore φ80mm, cylinder length 800mm
23. Cutting speed: 2 to 3 seconds / second
24. Large frame: channel steel welded frame
25. The blade guard box: steel plate welded
26. The blade cartridge bearings: 45 # thick-walled steel pipe, made of fine boring grinding
27. The blade shaft; 45 # steel after quenching grinding together
Three: the automatic control system advantages:
1. flying saw punching C steel equipment 7-roller leveling, the flat effect, drive coupling using the activity, and automatically disconnect the host, avoid the synchronization device is running hard to bring
2. Roll Die: The Gr15 (bearing steel), high hardness, wear resistance, generally 2 years no significant wear, hard chrome plated can increase wear resistance
3. Host an external nut adjustment, quick and easy replacement of utility models, the key hook 45 # steel finishing, hardening, cutting lines made of high hardness, never bend
4. Adjust set: The snap-in, easy to uninstall, interchangeability, easy to fall off, easy to replace
6. high degree of automation, save manpower, save time, the material standard

C/Z Shape Changeable Purlin Production Line

C/Z Shape Changeable Purlin Production Line

C or Z shape purlins are made from hot/cold rolled steel strips,and straightened,hole punched,cut to length,and roll formed by WLPM series C/Z changeable shape purlin roll forming machine. Through changing, this product line can make the change of the shape C or Z purlin,besides change different size of C or Z shape purlin,This change for shape and sizes of C/Z purlin can be realized by automatic mode,or manual adjusting mode.
WLPM series C/Z shape purlin product line consists of uncoiling system,straightening system,hole punching system,shearing system,roll forming system,products support table,hydraulic system,automatic controlling system,and so on. It’s a high efficiency equipment of making purlin,which is suitable for current enterprises.

C/Z Shape Changeable Purlin Production Line
Working Flow :
Uncoiling-Sheet Guiding-Straightening&Levelling-Hole Punching-Measuring Length&shearing-Roll Forming-Sheet to support table

C/Z Shape Changeable Purlin Production Line
Main Technical Parameters:

Item Parameters
Profile  C and Z purin
Material Type Steel strip
Thickness (mm) 1.0-3.2 1.0-3.0
Yield Stress(Mpa) 230-300 300-350
Max.Forming speed(m/min) 16-18
Roller Material D2
Roller driven type Hydraulic motor driven
Controller PLC
Operation  Touch screen and button
Hydraulic system pressure(MPA) 25
Hydraulic station motor power(KW) 7.5
Total power(kw) 30
Total weight(kg)  about 12000

C/Z Shape Changeable Purlin Production Line

 

If you want to buy the Fully automatic Interchange C/Z purlin roll forming machine you can contact us with email  roofingmachine@zhongtuocn.com

 

Steel Guardrail Roll Forming Machine

Steel Guardrail Roll Forming Machine

Introduction
Express road guardrail panel is made from hot rolled steel strips,and straightened,holes punched,roll formed,and cut to length by guardrail roll forming machine. The finished products are of many features. Such as high efficient,high automation,less labor.and etc.This machine integrates the technologies of cold roll forming,punching,automatic stack,and automatic controlling.

Steel Guardrail Roll Forming Machine
The guardrail roll forming machine consists of uncoiling system,straightening system,scrap edge cutting,leveling guillotine shearing system,holes punching system,cold roll forming system,cutting to length system,automatic stacker system,electric controlling system,hydraulic system,automatic controlling system,and so on.

Steel Guardrail Roll Forming Machine
Working Flow
Uncoiling-Sheet Guiding-Straightening&Leveling-Scrap Cutting-Holes Punching-Roll Forming-Cut to Length -Sheet to Support Table

Steel Guardrail Roll Forming Machine
Main Technical Parameters:

Item Parameters
Profile Two ribs and three ribs guardrail
 

Material

Type Steel strip
(mm)Thickness 2.5-4.0
(Mpa)Yield stress 230-300
(m/min)Max.Forming speed 20
Roller material D2
Roller driven type Gimbals transmission
Controller PLC
Operation Touch screen+button
(Mpa)Hydraulic system pressure 25
(kg)Total weight About 50000

Automatic C80-300C steel machine equipment

Automatic C80-300C steel machine equipment

1. Automatic C80-300C steel machine equipment configuration:
One arm coil discharge rack units, bearing 4T;
Wrap one set type inlet feed guide wheels automatically adjust the width according to the width of the material, automatic alignment;
Feed leveling one set;
CNC hydraulic punching one set, automatic control horizontal and vertical pitch;
One set of hydraulic shears, automatic cut to length;
Forming host, one (hydraulic transmission), according to the part of the C-beam size requirements automatically adjust pressure mold;
PLC computer control system of one set, touch screen;
One set of hydraulic station;
Finished tray feeder three months;
One set of random tools;
user’s Guide.

Automatic C80-300C steel machine equipment
2. Automatic C80-300C steel machine equipment technical parameters:
1. Size: 8000 * 1700 * 1650
2. Weight: 9T
3. Motor Power: 22kw
4. forming passes: 14 +5 Road Shaping
5. Roll speed: low speed 8m / min, speed 16m / min, high speed 25m / min
6. Effective Width: C80 x40-C300 x90mm
7. Roll Thickness: 1.2-3.0mm
8. Tolerance: ± 2mm
9. Roll Material: tool steel Gcr15, CNC machining after heat treatment to the hardness of 58-60, finishing / plating
10. Spindle material: 40Cr quenching 280-320HB, after finishing CNC
11. Cut System: Hydraulic shearing device
12. The molding material Scissors: Cr12MoV
13. The production of materials: Material Q235-Q345,
14. Machine Paint Colors: Blue

Automatic C80-300C steel machine equipment

3. Automatic C80-300C steel purposes:
Purlins, subject and medium-sized industrial civil buildings by the force structures, such as steel buildings, factories, warehouses, exhibition halls, theaters, stadiums, fairs trellis roof load and load-bearing wall flat support

4. Automatic C80-300C steel machine equipment Features:

Computer controlled, automatic change type, without manual exchange, C60-300 just one minute you can easily change any type, to achieve what you need to change the product type specifications into spout automatic adjustment, hydraulic punching automatic control horizontal and vertical pitch, cut to length, precision accuracy, pressure-type speed, no bell, every minute of the board 25-30m / min, saving labor costs, Increase productivity

If you wan to know more information about the 80-300 Broken C Purlines roll forming machine you can contact us with email  :  roofingmachine@zhongtuocn.com

700 Automatic shutter doors machine Products

700 Automatic shutter doors machine Products

700 type automatic shutter doors Technical Data Sheet
Equipment Total length: 10m width 1.3m height 1.8m
Motor power: 5.5Kw + 3Kw voltage 380V
Production speed: 8 – 10 m / min
Transmission: chain drive
Molding machine axis: 700 22 row axis. Large frame: 250H steel, upright plate 12mm
Shaft material: 45 # steel
Wheel Material: 45 # steel hard chrome plating
Forming part: Seiko-type wheel rotational molding, forming a good effect, reducing the friction between the wheels and raw materials, debugging convenient, fast.
CNC system: PLC panel, KEL-320 display
Counter: the use of domestic optical rotary encoder, A40S6-600-2-12-ACP
Cut: 3Kw Pumping Station

700 Automatic shutter doors machine Products
700 type automatic shutter door products for a variety of industrial plants, warehouses and other roofing production has a high peak, high strength advantage, lap install safe, reliable, waterproof and anti-riot units and strong performance characteristics, the aircraft production to solve the pressure plate conventional series pressure plate roof leakage problem, with the bagging machine can be made without beam vaulted roof.
(1) This device uses a high level of color steel automatic control software, production information management.
(2) the entire unit automation control system uses a highly integrated network, automation systems and better performance.
(3) Automatic shutter doors machine 700 also has the operation, maintenance, service and commissioning of machinery, molds advantages of easy replacement.

Rolling Shutter Machine Parts

Rolling Shutter Machine Parts

We manufacture a wide range of Rolling Shutter machines which are widely appreciated by our clients. Our production process conforms to various industrial standards which ensure qualitative output by utilizing the resources to an optimum level.

Rolling Shutter Machine Parts

Rolling Shutter Machine Parts

We manufacture these Rolling Shutter Machine Parts as per the industrial norms, in order to provide the clients optimum satisfaction. The offered machine parts offered by us are of the best quality, owing to their construction using high grade raw materials. Known to increase the efficiency of the rolling shutter machines, the parts provided by us are highly effective and asked for. Further, we provide these products at a rate which is quite reasonable.

Features:

High Quality

Good Service

Comparative Price